d r a ft this is information on a product in full production. 14 march 2014 docid17458 rev 2 1/8 HDMI05-CL01F3 5-line ipad?, hdmi? control line esd protection datasheet - production data figure 1. pin configuration (bump side) and schematic features ? low line capacitance ? high efficiency in esd protection ? lead-free package ? very thin package ? high reliability offered by monolithic integration ? high reduction of parasitic elements through integration and wafer level packaging complies with the standards: ? iec 61000-4-2 level 4 ? 15 kv (air discharge) ? 8 kv (contact discharge) ? iec 61000-4-2 level 1 ? 2 kv (air discharge) ? 2 kv (contact discharge) application where esd protection for hdmi control lines (cec, hpd, scl and sda) is required: ? mobile phones and communication systems ? portable multimedia players ? camcorder, digital still cameras description the HDMI05-CL01F3 chip is a low capacitance esd protection for hdmi control pins. it also integrates a pull-up resistor for i2c bus and a pull- down resistor for hot plug detect. the esd protection circuitry prevents damage to the protected device when subjected to esd surges up to 15 kv. 1. b2 and c2 bumps must be connected together in the pcb tm : ipad is a trademark of stmicroelectronics. hdmi, the hdmi logo and high-definition multimedia interface are trademarks or registered trademarks of hdmi licensing llc. leed-free flip-chip package (8 bumps) 3 2 1 a scl c b hpd sda cec gnd gnd 5v rpu a1 a3 a2 5v scl r3 cec b3 c3 c2 sda gnd hpd b2 c1 gnd r2 r1 www.st.com
d r a ft characteristics HDMI05-CL01F3 2/8 docid17458 rev 2 1 characteristics figure 2. electrical characteristics - definitions table 1. absolute maximum ratings (t amb = 25 c) symbol parameter value unit v pp external pins (a1, a2, a3, b3 and c3): esd iec 61000-4-2, level 4 - air discharge esd iec 61000-4-2, level 4 - contact discharge internal pin (c1): esd iec 61000-4-2, level 1 - air discharge esd iec 61000-4-2, level 1 - contact discharge 15 8 2 2 kv p d line resistance power dissipation at 70 c 60 mw t op operating temperature range -30 to + 85 c t stg storage temperature range -55 to + 150 c table 2. electrical characteristics (t amb = 25 c) symbol test condition min. typ. max. unit v br i r = 1 ma 14 v i rm v rm = 3 v per line 50 200 na r 1 , r 2 1575 1750 1925 r 3 80 100 120 k c line v line = 0 v, v osc = 30 mv, f = 1 mhz (measured under zero light conditions, b2 and c2 bumps connect together) 81012pf symbol parameter v = breakdown voltage i = leakage current @ v v = stand-off voltage c = line capacitance br rm rm rm line i v v br v rm i r i rm i rm i r v rm v br
docid17458 rev 2 3/8 d r a ft HDMI05-CL01F3 characteristics 8 figure 3. s21(db) versus frequency on a1 figure 4. analog crosstalk measurements b3- a3 100k 1m 10m 100m 1g -22 -20 -18 -16 -14 -12 -10 -8 -6 -4 -2 0 s21 (db) a1_0v a1_2.5v a1_3.6v a1_5.5v f(hz) -40 -35 -30 -25 -20 -15 -10 -5 0 crosstalk (db) - - - - - - - - 100k 1m 10m 100m 1g - - - - - - - - f(hz) b3_a3_0v b3_a3_2.5v b3_a3_3.6v b3_a3_5.5v figure 5. digital crosstalk measurement a3-b3 with 5 v applied on c1 figure 6. esd response to iec 61000-4-2 (+8 kv contact discharge) on cec line (a2) c1 c2 1 v/div 50 mv/div 20 ns/div 20 ns/div output input c2 20 v/div 20 ns/div vcl figure 7. esd response to iec 61000-4-2 (-8 kv contact discharge) on cec line (a2) figure 8. line capacitance versus reverse applied voltage on a2-b2 20 v/div 20 ns/div c2 vcl 0.0 2.0 4.0 6.0 8.0 10 10 12 14 0 2 4 6 8 c(pf) v (v) r
d r a ft typical application schematic HDMI05-CL01F3 4/8 docid17458 rev 2 2 typical application schematic figure 9. implementation with hdmi type c connector a1 a2 4 tmds channel hdmi driver a3 b1 b3 c1 c2 c3 esdaulc6-8f3 HDMI05-CL01F3 b2 cec 5v 2 x 1k75 5v scl sda hpd 100k 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 tmds data2 shield tmds data2 + tmds data2 - tmds data1 shield tmds data1 + tmds data1 - tmds data0 shield tmds data0 + tmds data0 - tmds clk shield tmds clk + tmds clk - ddc/ eec ground cec scl sda reserved +5v power hot plug detect type c hdmi connector
docid17458 rev 2 5/8 d r a ft HDMI05-CL01F3 ordering information scheme 8 3 ordering information scheme figure 10. ordering information scheme 4 package information ? epoxy meets ul94, v0 ? lead-free package in order to meet environmental requirements, st offers these devices in different grades of ecopack ? packages, depending on their level of environmental compliance. ecopack ? specifications, grade definitions and product status are available at: www.st.com . ecopack ? is an st trademark. figure 11. flip-chip dimensions hdmi 05 - cl 01 f3 function number of lines application version package hdmi = hdmi protection 05 = 5 lines cl = control lines 01 = without cec pull-up integrated f3 = flip-chip 0.4 mm pitch 400 m 40 400 m 40 170 m 255 m 40 605 m 55 1.14 mm 30 m 1.14 mm 30 m
d r a ft package information HDMI05-CL01F3 6/8 docid17458 rev 2 figure 14. flip-chip tape and reel specification figure 12. footprint figure 13. marking 220 m recommended 220 m recommended 260 m maximum solder stencil opening : copper pad diameter: solder mask opening: 300 m minimum x y x w z w dot, st logo ecopack status xx = marking z = manufacturing location yww = datecode (y = year user direction of unreeling all dimensions in mm 4.0 0.1 8.0 0.3 4.0 0.1 1.75 0.1 3.5 - 0.1 ? 1.5 0.1 0.69 0.05 1.24 1.24 st e xxz yww st e xxz yww st e xxz yww dot identifyng pin a1 location
docid17458 rev 2 7/8 d r a ft HDMI05-CL01F3 ordering information 8 5 ordering information 6 revision history table 3. ordering information order code marking package weight base qty delivery mode HDMI05-CL01F3 jn flip-chip 1.9 mg 5000 tape and reel (7?) table 4. document revision history date revision changes 30-apr-2010 1 initial release. 14-mar-2014 2 updated figure 9 .
d r a ft HDMI05-CL01F3 8/8 docid17458 rev 2 please read carefully: information in this document is provided solely in connection with st products. stmicroelectronics nv and its subsidiaries (?st ?) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described he rein at any time, without notice. all st products are sold pursuant to st?s terms and conditions of sale. purchasers are solely responsible for the choice, selection and use of the st products and services described herein, and st as sumes no liability whatsoever relating to the choice, selection or use of the st products and services described herein. no license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. i f any part of this document refers to any third party products or services it shall not be deemed a license grant by st for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoev er of such third party products or services or any intellectual property contained therein. unless otherwise set forth in st?s terms and conditions of sale st disclaims any express or implied warranty with respect to the use and/or sale of st products including without limitation implied warranties of merchantability, fitness for a particular purpose (and their equivalents under the laws of any jurisdiction), or infringement of any patent, copyright or other intellectual property right. st products are not designed or authorized for use in: (a) safety critical applications such as life supporting, active implanted devices or systems with product functional safety requirements; (b) aeronautic applications; (c) automotive applications or environments, and/or (d) aerospace applications or environments. where st products are not designed for such use, the purchaser shall use products at purchaser?s sole risk, even if st has been informed in writing of such usage, unless a product is expressly designated by st as being intended for ?automotive, automotive safety or medical? industry domains according to st product design specifications. products formally escc, qml or jan qualified are deemed suitable for use in aerospace by the corresponding governmental agency. resale of st products with provisions different from the statem ents and/or technical features set forth in this document shall immediately void any warranty granted by st for the st product or service described herein and shall not create or extend in any manner whatsoev er, any liability of st. st and the st logo are trademarks or register ed trademarks of st in various countries. information in this document supersedes and replaces all information previously supplied. the st logo is a registered trademark of stmicroelectronics. all other names are the property of their respective owners. ? 2014 stmicroelectronics - all rights reserved stmicroelectronics group of companies australia - belgium - brazil - canada - china - czech republic - finland - france - germany - hong kong - india - israel - ital y - japan - malaysia - malta - morocco - philippines - singapore - spain - swed en - switzerland - united kingdom - united states of america www.st.com
|
